Gradall Forklift Part

Gradall Forklift Part - The Gradall excavator was the creation of two brothers Ray and Koop Ferwerda. The excavator was established In the 1940's throughout World War II, when there was a shortage of workers. Partners in a Cleveland, San Bernardino construction company referred to as Ferwerda-Werba-Ferwerda, the brothers faced a huge predicament when lots of men left the labor force and signed up in the military, depleting available workers for the delicate finishing work and grading on highway projects. The Ferwerda brothers decided to make an equipment which will save their company by making the slope grading job less manual, easier and more efficient.

Their first design model was a device with two beams set on a rotating platform that was attached over a used truck. A telescopic cylinder moved the beams back and forth which enabled the fixed blade at the end of the beams to push or pull dirt. Before long enhancing the first design, the brothers built a triangular boom to add more strength. As well, they added a tilt cylinder which let the boom rotate 45 degrees in both directions. A cylinder was placed at the back of the boom, powering a long push rod to enable the machinery to be outfitted with either a blade or a bucket attachment.

Gradall launched in 1992, with the introduction of the new XL Series hydraulics, the most ground-breaking adjustment in their machinery ever since their creation. This new system of top-of-the-line hydraulics allowed the Gradall excavator to deliver comparable power and high productivity to the more traditional excavators. The XL Series ended the first Gradall equipment power drawn from gear pumps and low pressure hydraulics. These traditional systems efficiently handled grading and finishing work but had a hard time competing for high productivity jobs.

The new XL Series Gradall excavators proved a remarkable increase in their lifting and digging ability. These versions were manufactured along with a piston pump, high-pressure hydraulics system that showed great improvements in boom and bucket breakout forces. The XL Series hydraulics system was even developed with a load-sensing capability. Conventional excavators use an operator to choose a working-mode; where the Gradall system could automatically adjust the hydraulic power intended for the work at hand. This makes the operator's whole task easier and also saves fuel at the same time.

Once the new XL Series hydraulics became available in the market, Gradall was thrust into the very competitive industrial machine market which are meant to deal with demolition, pavement removal, excavating and other industrial jobs. The introduction of the new telescoping boom helped to further improve the excavator's marketability. The telescoping boom gives the excavator the ability to work in low overhead areas and to better position attachments.

Click to Download the pdf

Forklift Parts

Parts for Electric Pallet Jack

Part for Electric Pallet Jack - Pallets are quite a vital part of the manufacturing industry and pallet handling could be done through various ways. Hand jacks, pallet racks, forklifts and pallet trucks are some of equipment most often utilized for pallet handling in the modern work place. Inside a manufacturing office, most pallets are normally stacked on big steel...

More

---

Forklift Fork Extension

Fork Extension for Forklift - Forklift extensions are a terrific choice when there is a need to reach further than your current blades would allow. In some circumstances whenever you have a load which exceeds more than can be safely picked up on your lift truck, an extension can help you do your job safely. Increasing Lift Truck Efficiency Forklift...

More

---

Crown Forklift Parts

Crown Forklift Parts - The Crown company was founded in 1945 by two brothers, Allen A. Dicke and the late Carl H. Dicke. Carl's son and Chairman Emeritus, James F. Dicke, joined the family business later that same year. At present, his son, James F. Dicke II, is Chairman and CEO. James F. Dicke III, serves as the company President...

More

---

Bale Clamps

Bale Clamp - Mainly useful for lifting or stacking a whole lot of goods, bale clamps can be utilized as a hydraulic lift truck or forklift attachment able to lift bales without using a pallet. Bar arm clamps are actually additional attachments which could be connected to allow the person operating it to lift cylindrical objects such as rolls of...

More

---

Forks for Forkflifts

Forklift Fork - Each and every time equipment parts get old they need to be replaced. A company can really save substantial amounts of cash when they replace just the part which gets old versus replacing the entire piece of machinery. Additional savings are accessible usually whenever replacing parts, there is the option to purchase used parts compared to brand...

More

---

High Reach Forklift Part

High Reach Forklift Part - Used in nearly all warehouse operations, boat yards or industrial construction sites, the lift truck is a vital component in order to help pick up and transport supplies. The reach feature of a forklift could help improve the applications that the forklift can accomplish such as stacking pallets on a high shelving unit. A forklift...

More

---

Fuel Tanks for Forklift

Fuel Tank for Forklift - The majority of fuel tanks are built; however several fuel tanks are made by experienced craftspeople. Restored tanks or custom tanks can be used on aircraft, automotive, tractors and motorcycles. There are a series of certain requirements to be followed when making fuel tanks. Usually, the craftsman sets up a mockup to be able to...

More

---

Clamp Forklift Attachments

Clamp Forklift Attachments - Making use of forklifts on the job location could ensure the safety of workers by significantly lessening their physical workload. In any business or factory, employee safety is the main concern. Materials must be stored, lifted and transported within the premises without causing any injury to all of the employees. Lift trucks are usually utilized in...

More

---